The door molding on the outside... Yellow and cracked
+ Reply to Thread
Results 1 to 7 of 7

This is a discussion on The door molding on the outside... Yellow and cracked within the Exterior & Appearance forums, part of the Tech & Modifying & General Repairs category; Well the molding on my door on the outside has cracked, and turned yellow.. Looks like it's been out in ...

  1. #1
    Nerdus Socialis MarkkInNj's Avatar
    Join Date
    Apr 2014
    Location
    Bergen County
    Posts
    2,295
    I Support ClubWRX

    The door molding on the outside... Yellow and cracked

    Well the molding on my door on the outside has cracked, and turned yellow.. Looks like it's been out in the sun for years. But oh wait? It's only been one and a half.. But this is on just this one.. Can I replace these at a dealer?

    It looks terrible in person.




    Sent from my iPhone using Tapatalk
    Last edited by MarkkInNj; 12-19-2015 at 11:49 AM.
    Brain Blast!

    My build: Minimal. http://www.clubwrx.net/forums/builds...han-never.html
    My Watch business Journey:http://www.clubwrx.net/forums/off-to...g-journey.html

    2014 ISM Hatch (Mine)
    2015 Premium CVT CWP (Me lady)

  2. Remove Advertisements
    ClubWRX.net
    Advertisements
     

  3. #2
    Registered User XJman's Avatar
    Join Date
    Feb 2015
    Location
    At work
    Posts
    3,835
    Yeah that's aftermarket and just included at some dealerships. Mine doesn't even have it.

    It should just slide over the edge of the door, so it should pull off. Be wary itll be full of junk behind it from road grime and wax. Clean it all up good and put a new strip on. Napa used to sell it by the roll in several colors that was uv resistant for a few bucks a roll

    Sent from my Nexus 6 using Tapatalk

  4. #3
    Water.....sometimes waves rqjoe's Avatar
    Join Date
    Feb 2015
    Location
    Ohio
    Posts
    777
    I Support ClubWRX
    They came stock? I don't have them. Looks like stuff I have added on past cars, from any autoparts store. They are just stuck on.

  5. #4
    Nerdus Socialis MarkkInNj's Avatar
    Join Date
    Apr 2014
    Location
    Bergen County
    Posts
    2,295
    I Support ClubWRX
    Quote Originally Posted by XJman View Post
    Yeah that's aftermarket and just included at some dealerships. Mine doesn't even have it.

    It should just slide over the edge of the door, so it should pull off. Be wary itll be full of junk behind it from road grime and wax. Clean it all up good and put a new strip on. Napa used to sell it by the roll in several colors that was uv resistant for a few bucks a roll

    Sent from my Nexus 6 using Tapatalk
    Quote Originally Posted by rqjoe View Post
    They came stock? I don't have them. Looks like stuff I have added on past cars, from any autoparts store. They are just stuck on.
    Aftermarket!? Sweet,. I'll just get rid of it then.

    Yep. Came with the car from the dealer. Didn't even think to look outside at the 15. Doesn't have it. I also have the wheel well ones, black the dealer put on my car, and clear bra around doors, fenders, and rocket panel that was on the car when I bought it. Didn't pay for it either..


    Sent from my iPhone using Tapatalk
    Brain Blast!

    My build: Minimal. http://www.clubwrx.net/forums/builds...han-never.html
    My Watch business Journey:http://www.clubwrx.net/forums/off-to...g-journey.html

    2014 ISM Hatch (Mine)
    2015 Premium CVT CWP (Me lady)

  6. #5
    Registered User XJman's Avatar
    Join Date
    Feb 2015
    Location
    At work
    Posts
    3,835
    I would get anything around my fenders that could hold moisture out of there. Same with the rocker pannels. But it will prevent chips at the cost of holding moisture

    Sent from my Nexus 6 using Tapatalk

  7. #6
    Nerdus Socialis MarkkInNj's Avatar
    Join Date
    Apr 2014
    Location
    Bergen County
    Posts
    2,295
    I Support ClubWRX
    Quote Originally Posted by XJman View Post
    I would get anything around my fenders that could hold moisture out of there. Same with the rocker pannels. But it will prevent chips at the cost of holding moisture

    Sent from my Nexus 6 using Tapatalk
    Yeah I'm stripping all the rubber stuff. The clear bra I'll keep, but the rubbers gone. Thanks guys! Lol




    Sent from my iPhone using Tapatalk
    Brain Blast!

    My build: Minimal. http://www.clubwrx.net/forums/builds...han-never.html
    My Watch business Journey:http://www.clubwrx.net/forums/off-to...g-journey.html

    2014 ISM Hatch (Mine)
    2015 Premium CVT CWP (Me lady)

  8. #7
    Registered User XJman's Avatar
    Join Date
    Feb 2015
    Location
    At work
    Posts
    3,835
    No prob

    Sent from my Nexus 6 using Tapatalk

+ Reply to Thread

Quick Reply Quick Reply

Register Now

Please enter the name by which you would like to log-in and be known on this site.

Please enter a password for your user account. Note that passwords are case-sensitive.

Please enter a valid email address for yourself. We strongly suggest that you stay away from using aol, yahoo, msn, and hotmail accounts. Sometimes the mail server blocks the emails from our server. As a result you will not receive any notifications including the confirmation email.

Please select your insurance company (Optional)

Log-in

Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.


Posting Permissions

  • You may post new threads
  • You may post replies
  • You may not post attachments
  • You may not edit your posts
  •